Connecting a wood stove to my furnaces chimney - Homesteading Today
Homesteading Today

Go Back   Homesteading Today > Country Living Forums > Alternative Energy

Alternative Energy Sponsored by LPC Survival


Reply
 
LinkBack Thread Tools Rate Thread
  #1  
Old 09/12/06, 05:22 PM
NJ Rich
 
Join Date: Dec 2005
Location: Springsteen Area of New Jersey
Posts: 1,147
Question Connecting a wood stove to my furnaces chimney

There is a upright round wood stove I can get for free. It isn't one of those "air tight effiecent models". I really don't care about that. I am thinking of getting it to supply heat if the natural gas fuel supply is interrupted.

I would want to disconnect the gas furnace exhaust and connect the wood stove to the cement block chimney. I can do the pipe work and have it ready if the need comes about. The flue pipe connection we have is 6 inches. The distance from the top of the wood stove to the chimney connection is about 20". I think the stove pipe is different than that used for natural gas. If I am correct and need a different pipe please put me on track to get the right material.

Has anyone done this? Are there any problems I should be aware of? Of course I would shut off the gas and power to the furnace before making this change over. Help.... NJ Rich

__________________
Reply With Quote
  #2  
Old 09/12/06, 10:34 PM
 
Join Date: Jan 2004
Location: MN
Posts: 7,176

Currently it is not to code to share a chimney between oil & wood stoves. Tho there is not a big chance of problem.

It has been totally illegal to place gas & wood appliances on the same chimney. Real potential for a problem there.

I'd think long & hard on this one before trying it....

--->Paul

__________________
Reply With Quote
  #3  
Old 09/13/06, 04:38 AM
 
Join Date: Jul 2004
Location: Michigan
Posts: 328

The pipe you're looking for is black and is a heavier material than dryer vent. It's available at Home Cheapo although early in the season they may be sold out of some of the componets. Make sure to put a cast iron damper on the flue to help control the burn and depending on the dynamics of the chimney, you may need a barometric damper if it drafts too strong. Absolutely do not use anything else other than "stove" pipe. You can potentially see flue temperatures of 800-1000 degrees F; that's what stove pipe is designed for.
As far as violating any codes, if you're unhooking the gas furnace and hooking up the wood furnace, both are not coneected at the same time. If the chimney is going to be used for wood it should have a cleanout port at the base to remove ash & soot.

__________________
Reply With Quote
  #4  
Old 09/13/06, 07:19 AM
Ross's Avatar
 
Join Date: May 2002
Location: Ontario
Posts: 12,470

Wood oil combo's can be to code, certainly here In Ontario it is. Wood +gas, I couldn't say, but you'd want to use that lined block chimney and not the Gas B vent (or oil's L vent as it's not insulated) ! Check the clay liner (assuming it has a clay liner) isn't flaking off from condensation and freezing from the gas exhaust. Not a lot of heat goes up a gas vent! You may need to reline the chimney. Stove pipe for a wood burner is black as the stack temp will go above 700 degrees F and that will cause the galvanizing to flake off regular C vent pipe. You connect wood stove vent backwards from oil so it's the crimped narrow end into the stove and the next into that pipe leaving the wide end to towards the chimney. Not as smoke tight BUT if you have a chimney fire from cresote the burning molten tar runs down the pipe into the stove and not out of the pipes in an open air flaming mass!

__________________

Do not meddle in the affairs of Dragons, for you are crunchy and good with ketchup........

Reply With Quote
Reply



Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -5. The time now is 07:31 PM.